diff --git a/BOM.csv b/BOM.csv index 03bae07..a04731d 100644 --- a/BOM.csv +++ b/BOM.csv @@ -17,6 +17,7 @@ Electronics,2,5819,Schottky Diode,SOD-123,D4 D5,C64885,0.090075,0.18015,"Used to Electronics,1,TYPE-C-16P-FH,Type-C Connector,SMD,J1,C709357,0.537857,0.537857,Detailed models refer to drawings. Electronics,1,2 Pin,XH Pin Header,PTH,JP1,C5341201,0.10188,0.10188,Detailed models refer to drawings. Electronics,1,4 Pin,2510 Pin Header,PTH,JP3,Taobao,0.08,0.08,https://m.tb.cn/h.5xQs6Mhxx7MnwSl?tk=3AZoWoS7zzc +Electronics,0,2 Pin,DC005-5.5X2.5,PTH,JP4,Taobao,0.07,0,https://m.tb.cn/h.ge11YE1cVjtWLr9?tk=rYvOWDYYVi4 Electronics,1,5.6uH,Buck-Boost Inductor,12XX,L1,C408522,4.49,4.49, Electronics,1,Green,Chip LED,0603,LED1,C84267,0.096338,0.096338,Greater than 65W Indicator (This is almost impossible to happen). Electronics,1,Red,Chip LED,0603,LED2,C84263,0.059304,0.059304,Battery charging indicator. @@ -45,7 +46,7 @@ Electronics,1,RV097NS R1S1 10kOhm,Potentiometer,PTH,VR1,Taobao,0.9,0.9,https://m Electronics,0,5000mAH,Li-ion Battery,21700,Battery,Taobao,16.9,0, Electronics,0,2 Pin,XH Pin,Wiring,JP1,Taobao,0.02,0,https://m.tb.cn/h.5xA4rsZ7O6otBoX?tk=l3hIWoSk1EH Module,0,3S 12.6V,Li-ion Battery Protection Module,Wiring,JP1,Taobao,6.33,0,https://m.tb.cn/h.5xAeXbW3B9YVp9a?tk=P89VWoSj9sX -Module,1,3S 12.6V,Li-ion battery level indicator Module,Wiring,JP2,Taobao,6.5,6.5,https://m.tb.cn/h.5C8AmuhibY3OzK3?tk=SOJpWoS8mzm +Module,1,3S 12.6V,Li-ion Battery Level Indicator Module,Wiring,JP2,Taobao,6.5,6.5,https://m.tb.cn/h.5C8AmuhibY3OzK3?tk=SOJpWoS8mzm Module,1,3S 12.6V XH2.54 Female No. 2 Wire Sequence,Lithium Battery Pack,Wiring,JP1,Taobao,79,79,https://m.tb.cn/h.5ArwGGE8BjNeA4H?tk=7LZaWqBgcbV Module,1,12V 1.65A,Toggle Switch,Wiring,JP2,Taobao,0.104,0.104,https://m.tb.cn/h.gb9f84NBrwxm58f?tk=FT8TWsMOmpE Wire,450,AWG24,Silicone Soft Wire,-,-,Taobao,0.00064,0.288, diff --git a/README.md b/README.md index 6090f8d..b50395b 100644 --- a/README.md +++ b/README.md @@ -4,6 +4,8 @@ A Simple Rechargeable Cylinder Fan for Fursuit Heads ## Installation +> **Note**: The BOM.csv is based on the Type-C with finished battery variant, if you choose another variant please read below first. + ### PCB First, solder the components to the PCB, you can refer to the method provided in the [Link](https://www.myredstone.top/archives/5215). @@ -11,9 +13,11 @@ First, solder the components to the PCB, you can refer to the method provided in The non-silkscreened 0Ohm resistor next to U3 is used to configure the fan PWM positive and negative. For DV05028B12U, use the 0Ohm resistor to connect pad closest to **inside** PCB (positive PWM). -The JP2 connector is used to connect the battery level indicator module, so **don't** solder XH2.54-2P. +The JP2 connector is used to connect the battery level indicator module, so **don't** solder PZ2.54-2X2P. -You can refer to the following procedure to verify that the PCB is working, and reproduce the soldering of J1 or U1 if there is an abnormality. +If you choose the DC version, you only need to solder C21 C22 JP1 JP3 JP4 R23 R24 R25 R26 U2 U3 VR1. + +If you choose the Type-C version, You can refer to the following procedure to verify that the PCB is working, and refer FAQ if there is an abnormality. > **Note**: No abnormally high temperatures in the IC and other components throughout the process. @@ -52,7 +56,9 @@ You can refer to the following procedure to verify that the PCB is working, and **CylinderFan-Nozzle-\*.stl** - Add support to the outer circle below. Pause the print and add the magnet while the magnet hole closes the layer. -**CylinderFan-Electronic-Body.stl** - Print the LED translucent faces with a white filament. Add support to bottom slide. +**CylinderFan-Electronic-Body-\*.stl** - Select one of the DC and Type-C versions to print. + +**CylinderFan-Electronic-Body-Type-C.stl** - Print the LED translucent faces with a white filament. Add support to bottom slide. **CylinderFan-Electronic-KnobRing.stl** - Print with TPU and controlle damping through fuzzy skin. @@ -60,7 +66,15 @@ You can refer to the following procedure to verify that the PCB is working, and ### Assembly -Just assemble according to CAD drawings. +A total of three to five AWG24 wires are required: + +- **Red** - Connect pin 1 of the toggle switch to pin 4 of PCB JP2. +- **Yellow** - Connect pin 2 of the toggle switch to pin 3 of PCB JP2 and the positive of the Li-ion battery level indicator module. +- **Black** - Connect pin 3 of the toggle switch to pin 2 of PCB JP2 and the negative of the Li-ion battery level indicator module. + +Be careful to route these wires through CylinderFan-Electronic-KnobTop.stl and CylinderFan-Electronic-Potentiometer.stl and not to impede the rotation of the structure. + +The other parts are simply assembled according to the CAD drawings. Be careful **NOT** to allow parts to run over, wrap around, or rub the wires.